Difference between revisions of "stoney cloud: Demo-System Installation"
| [unchecked revision] | [unchecked revision] |
(→Overview) |
(→Installation) |
||
| Line 17: | Line 17: | ||
= Installation = | = Installation = | ||
| + | == Booting == | ||
| + | Choose '''1) FOSS-Cloud Installer: default boot options''' | ||
| + | |||
| + | [[Image:stoney_cloud_demo-system_01.png||600px]] | ||
| + | |||
| + | == Keymap Selection == | ||
| + | |||
| + | Set the desired keymap. The following example works for the German speaking part of Switzerland: '''46 (de_CH)''' | ||
| + | |||
| + | [[Image:stoney_cloud_demo-system_02.png||600px]] | ||
| + | |||
| + | == Start the Installation == | ||
| + | Start the actual installation by typing: '''yes''' | ||
| + | |||
| + | [[Image:stoney_cloud_demo-system_03.png||600px]] | ||
| + | |||
| + | == Choose the Single-Node Installation == | ||
| + | Choose the Single-Node Installation by typing: '''2''' | ||
| + | |||
| + | [[Image:stoney_cloud_demo-system_04.png||600px]] | ||
| + | |||
| + | == Device Selection == | ||
| + | You'll need to select a SCIS, SATA, PATA or virtual disk. The following installation in done in a virtualized environment, therefore we choose the virtual disk: '''vda''' | ||
| + | |||
| + | [[Image:stoney_cloud_demo-system_05.png||600px]] | ||
| + | |||
| + | If you type yes, you'll be deleting all the existing data on the chosen disk: '''yes''' | ||
| + | |||
| + | [[Image:stoney_cloud_demo-system_06.png||600px]] | ||
| + | |||
| + | == Proceeding ... == | ||
| + | The installation proceeds with the partitioning of the disk and the installation of the operating system: | ||
| + | |||
| + | You can ignore the message "Error: /dev/vda: unrecognised disk label" as this is normal for a first installation in a virtual disk. | ||
| + | |||
| + | [[Image:stoney_cloud_demo-system_0yes.png||600px]] | ||
| + | |||
| + | [[Image:stoney_cloud_demo-system_09.png||600px]] | ||
| + | |||
| + | == Network == | ||
| + | Now we configure the network. In this example, we only have one network interface: '''eth0''' | ||
| + | |||
| + | [[Image:stoney_cloud_demo-system_10.png||600px]] | ||
| + | |||
| + | We choose the automatic DCHP configuration: '''yes''' | ||
| + | |||
| + | [[Image:stoney_cloud_demo-system_11.png||600px]] | ||
| + | |||
| + | == Reboot == | ||
| + | Now we can reboot the system: | ||
| + | |||
| + | [[Image:stoney_cloud_demo-system_12.png||600px]] | ||
| + | |||
== Skipping Checks == | == Skipping Checks == | ||
To skip checks, type '''no''' when asked: | To skip checks, type '''no''' when asked: | ||
Revision as of 11:12, 7 April 2014
Contents
Overview
The stoney cloud builds upon various standard open source components and can be run on commodity hardware. The Demo-Node installation consists of one node with the following software-stack installed:
- The Linux kernel based virtualization technology.
- An OpenLDAP Directory Server for the storage of the stoney cloud user and service related data with the web based management VM-Manager interface and the Linux kernel based virtualization technology.
Prerequisites
The following items and conditions are required to be able to install and configure a stoney cloud environment:
- A dedicated server which fulfils the following requirements:
- 64-Bit Intel with VT-Technologie (AMD is not tested at the moment, but it should work).
- 8 Gigabyte Memory (more is better).
- 130 Gigabyte up to 2 Terabyte disks (for the first RAID-Set, the 2 Terabyte restriction applies).
- For the mass storage (where the virtual machines are stored) we recommend a second RAID-Set configured as RAID6-Set with battery backup.
- One physical Ethernet Interfaces.
Limitations
During the installation of the Gentoo Linux operating system, the first physical Ethernet Interface ist automatically configured with DHCP. This means, you need a working DHCP Server. The virtual machines running on the stoney cloud Demo-System are NATed. This means, you can not access the virtual machines from externally.
Installation
Booting
Choose 1) FOSS-Cloud Installer: default boot options
Keymap Selection
Set the desired keymap. The following example works for the German speaking part of Switzerland: 46 (de_CH)
Start the Installation
Start the actual installation by typing: yes
Choose the Single-Node Installation
Choose the Single-Node Installation by typing: 2
Device Selection
You'll need to select a SCIS, SATA, PATA or virtual disk. The following installation in done in a virtualized environment, therefore we choose the virtual disk: vda
If you type yes, you'll be deleting all the existing data on the chosen disk: yes
Proceeding ...
The installation proceeds with the partitioning of the disk and the installation of the operating system:
You can ignore the message "Error: /dev/vda: unrecognised disk label" as this is normal for a first installation in a virtual disk.
Network
Now we configure the network. In this example, we only have one network interface: eth0
We choose the automatic DCHP configuration: yes
Reboot
Now we can reboot the system:
Skipping Checks
To skip checks, type no when asked:
Do you want to start the installation? yes or no?: no
Then manually restart the stoney cloud installer with the desired options. For example
/mnt/cdrom/foss-cloud-installer -c
Options:
-c: Skip CPU requirement checks -m: Skip memory requirement checks -s: Skip CPU and memory requirement checks
